Follow animatedknots on Twitter
Advert
Animated Knots by Grog

TIE KNOTS THE FUN AND EASY WAY

Better to know a knot and not need it, than need a knot and not know it.

Cleat Hitch (Dock Line)

indeximageindeximageIndexLeft
Boating Index Boating Usage

Alpine Butterfly Bend Alpine Butterfly Loop Anchor Hitch Ashley Stopper Knot Bowline Bowline on a Bight Bowline, Running Buntline Hitch Carrick Bend Chain Splice Cleat Hitch (Deck) Cleat Hitch (Halyard) Clove Hitch (End) Constrictor (Twisting) Double O'hand Stopper EStar Stopper Knot Eye Splice Figure 8 Icicle Hitch (Loop) Halyard Hitch Heaving Line Knot Lighterman's Hitch Midshipman's Hitch Pile Hitch Rat-Tail Stopper Rolling Hitch Round Turn & Hitches Soft Shackle Soft Shackle Edwards Trucker's Hitch Stevedore Stopper Zeppelin Bend

Knot Terminology Knot & Rope Safety Rope Properties Contact About
Use the Arrow Keys or hover over the Buttons above. View Video

Cleat Hitch for a Dock Line Tying

Do not bring the line around the near horn. Go around the far horn, then around the other, and back across the middle. Continue making several more figure 8 turns around each horn.

Cleat Hitch for a Dock Line Details

Uses: The Cleat Hitch secures a rope to a cleat. It is deceptively simple and an unwary skipper who invites visitors to cleat a mooring line may be astonished and dismayed by the unsatisfactory results. See also using a cleat hitch for Securing a Halyard.

First Horn: Initially the rope must be led round the most distant horn of the cleat followed by a turn in the same direction round the other horn. Starting round the wrong horn increases the risk of a jam.

Name: Some contributor's protest that the name "Hitch" is wrongly applied because there is no final Half Hitch. However, Cleat Hitch describes the purpose well – the rope is hitched to a cleat – and there are other "Hitches" that are sometimes used without a final Half Hitch, e.g., Tensionless and Lighterman's (Tugboat).

No Round Turn: After passing the rope around two horns of the cleat, always cross over and make figure 8 turns afterwards. This is because the Figure 8 Turns lift the rope up against the horns and out of the way of the first turn. There is a risk if the initial turn continues around and under the first horn a second time (making a complete round turn). Now if a towline briefly becomes slack, the initial turn can separate away from the cleat and then clamp down on top of the second turn making it impossible to release the rope while there is load on the towline.

No Locking Hitch? Several skippers have written to emphasize various situations when a Locking Half Hitch must be avoided:

  • Large Vessels: The uniform practice on large vessels is to never add a final Half Hitch.
  • Towing: Never add a Half Hitch on either end of a towline. First, a towline should always be monitored. Second, the ability to quickly release either end is essential.
  • Sheeting a Sail: Avoid a Half Hitch for the sheet controlling a sail – rapid release may be critically important in preventing a disaster, e.g., a capsize.

Use a Locking Hitch? In other situations a locking hitch is commonly used, e.g., the dock lines for a yacht left in a harbor, the halyards cleated to the mast, and flag halyards.

Number of Turns: In most of Ashley's illustrations he shows astonishingly few turns. However, he was writing when tarred hemp was the rope of choice. Today's ropes may be stronger, thinner, slippery, and more elastic (nylon rope stretches by more than 5% when loaded to 20% of its rated breaking strain). Some modern illustrations still show only a single crossover followed by a Half Hitch. An intermittent load on a nylon rope may transmit tension to the Half Hitch and make release awkward. I am indebted to Kevin Redden for the following practical advice: two crossovers is the bare minimum, and only for temporary use in sheltered conditions. In all other situations, always add more – certainly enough to handle any storm load.

History: "Belaying a rope" means securing it or making it fast. Before cleats were common, a rope used to be secured to a vertical pin in a wooden beam called, of course, a "Belaying Pin". Ashley describes several variations including the use of a single hitch by itself (ABOK # 1594, page 284).

Acknowledgements: Several people have written to provide suggestions about this knot. In particular it is a pleasure to thank Kevin Redden who explained the risk of using a full round turn and provided a recommendation about the number of crossover turns.

Disclaimer: Any activity that involves ropes is potentially hazardous. Lives may be at risk - possibly your own. Considerable attention and effort have been made to ensure that these descriptions are accurate. However, many critical factors cannot be controlled, including: the choice of materials; the age, size, and condition of ropes; and the accuracy with which these descriptions have been followed. No responsibility is accepted for incidents arising from the use of this material.

Copyright © 2007 - 2014
All Rights Reserved Grog LLC
    Copyright and Trademark    
Version 4.0.1. Nov 24, 2014

iPad App – New

ipad More Options
Full Screen
Features ++

iPhone App

iPhone Updated Version
Added Sections
More Features

Android App

Android PhoneUpdated Version
Move to SD Card
Added Sections

Half Price Offer

Rope Chafe Wear Pads
Self-Adhesive Stainless Steel
Prevent Fiberglass Chafe. WearPad Order Wear Pads